Skip to content

Black Friday: 7% off with code BLACKMONTH7, limited time only!

Pay in 3 to 84 instalments with Siko on eligible purchases.
View your basket

Electric scooter tyre pressure: the chart by wheel size and by model

The tyre pressure for every scooter in our catalogue, taken from the manufacturer's manual, in psi and bar, sorted by wheel size. Plus the effect of weight and cold, how to read the sidewall and a routine for checking.

Benjamin Gayaud

Benjamin Gayaud

9 min read

Dial pressure gauge fitted on the valve of an electric scooter wheel

Maintenance

Most Dualtron scooters take 50 psi, or 3.45 bar.

The essentials

On most Dualtron and Rovoron scooters, the Minimotors manual gives 50 psi, or 3.45 bar, a single figure for both wheels⁠[10]. There are exceptions. The Dualtron X Limited and its 13-inch tyres take 32 psi⁠[17], the InMotion RS 40 psi or 2.8 bar⁠[14], and the Teverun Mini range between 3.1 and 3.44 bar⁠[6]. Measure the pressure with the tyres cold, using a gauge, and never go above the maximum moulded on the tyre sidewall⁠[33].

50 psi

or 3.45 bar: most Dualtron and Rovoron scooters

2 weeks

at most between two checks, according to Michelin

32 psi

or 2.21 bar: the Dualtron X Limited

0.07 to 0.14 bar

lost for every 10 °C drop, according to Continental

  • The pressure to follow is the one in your model's manual. The tables below give it for every scooter in our catalogue whose manufacturer publishes it.
  • Measure it cold, with a gauge, at least once a month, every two weeks if you ride often, and before a long ride.
  • The figure on the sidewall is a maximum, not a target. Never go above it.
  • Cold lowers the pressure. In winter, check it at the temperature you ride in.
  • Too low, the pressure causes punctures and damages the tyre. Too high, it reduces grip.

What pressure for a 9 or 10-inch scooter?

Each figure comes from the manufacturer's manual. The first unit is the one in the manual, the second is converted (1 psi is 6.894757 kPa, 1 bar is 100 kPa⁠[28]). The tyre type is the one stated in the manual. It can change from one production run of a model to another: if in doubt, read your sidewall, which says ‘Tubeless’ or ‘Tube type’⁠[29].

ModelOriginal tyre according to the manualPressure
Dualtron Forever10-inch, inner tube50 psi (3.45 bar)⁠[1]
Dualtron Spider Max10 × 2.5, inner tube50 psi (3.45 bar)⁠[2]
Dualtron Victor Limited10 × 3.0-6.5, tubeless50 psi (3.45 bar)⁠[3]
Dualtron Victor Luxury +10-inch wide, inner tube50 psi (3.45 bar)⁠[4]
Rovoron R5 and R5 Pro10 × 3.0-6.5, tubeless50 psi (3.45 bar) in the spec sheet, 32 to 38 psi (2.21 to 2.62 bar) in the maintenance table⁠[5]
Teverun Fighter Mini and Blade Mini10-inch3.1 to 3.44 bar (45 to 50 psi)⁠[6]
Nami Klima, Klima Max and Klima One10 × 3.050 psi (3.45 bar) on both tyres
Nami Stellar and Super Stellar9 × 2.550 psi (3.45 bar) on both tyres
Figures recorded on 17 November 2026. The Nami figures come from the Nami manuals.

We could not find the Nami manuals on any of the manufacturer's websites. We make them available as they are, along with all the others, in our documents. The four Nami manuals (Klima, Stellar, Blast Max and Burn-E) say the same thing: 50 psi recommended on both tyres, and 50 psi at most when you re-inflate.

What pressure for an 11-inch scooter?

A 90/65-6.5 tyre is about 11 inches in diameter: the calculation is in our tyre article. The words ‘runflat’ and ‘self-sealing’ are the ones used in the Minimotors manuals: what they change when you get a puncture is explained in our puncture article.

ModelOriginal tyre according to the manualPressure
Dualtron Achilleus11-inch wide, tubeless50 psi (3.45 bar)⁠[7]
Dualtron Storm Limited11-inch wide, ‘run-flat’50 psi (3.45 bar)⁠[8]
Dualtron Sonic Alien11-inch, ‘runflat’50 psi (3.45 bar)⁠[9]
Dualtron Thunder 311-inch, ‘runflat’50 psi (3.45 bar)⁠[10]
Odyssr Alpha (Dualtron Thunder 2)11-inch, ‘self-sealing’50 psi (3.45 bar)⁠[11]
Rovoron R7 and R7 Pro90/65-6.5, tubeless50 psi (3.45 bar) in the spec sheet, 32 to 38 psi (2.21 to 2.62 bar) in the maintenance table⁠[12]
Rovoron S711-inch, tubeless50 psi (3.45 bar) in the spec sheet, 32 to 38 psi (2.21 to 2.62 bar) in the maintenance table⁠[13]
InMotion RS and RS Lite11-inch, tubeless40 psi or 2.8 bar, within a range of 2.5 to 3.5 bar (36 to 51 psi)⁠[14]⁠[15]
InMotion RS Jet11-inch, tubeless40 psi or 2.8 bar, within a range of 2.5 to 3.5 bar (36 to 51 psi)⁠[16]
Nami Blast Max11-inch50 psi (3.45 bar) on both tyres
Nami Burn-E and Burn-E Max11-inch, 283 mm tall when inflated50 psi (3.45 bar) on both tyres
Figures recorded on 17 November 2026. The Nami figures come from the Nami manuals.

Rovoron: two figures in the same manual

The manuals for the Rovoron R5, R7 and S7 give 50 psi in their spec sheet and 32 to 38 psi in their maintenance table, a few pages further on⁠[5]⁠[12]⁠[13]. The spec sheet figure is the one Minimotors gives for all its other 11-inch scooters in this table. Either way, the maximum moulded on your tyre remains the limit.

What about 12, 13 and 15-inch wheels?

ModelOriginal tyre according to the manualPressure
Kaabo Wolf King GTR12-inch tubeless, road or off-road350 kPa, or 3.5 bar (51 psi)
Dualtron X Limited13-inch wide, tubeless32 psi (2.21 bar)⁠[17]
Dualtron City15-inch wide, inner tube50 psi (3.45 bar)⁠[18]
Figures recorded on 17 November 2026. The Kaabo figure comes from the Kaabo manual.

The X Limited shows that wheel size does not tell you the pressure. With its wide 13-inch tyres, it takes much less than the brand's 11-inch models. So never copy the figure from another model, even a similar one. As with Nami, we could not find the Kaabo manual on any of the manufacturer's websites: it is in our documents.

Is your model not in these tables?

Many older scooters are still on the road, and we sell parts for them. Here are the figures from their Minimotors manuals. Three of them differ from the usual 50 psi.

ModelOriginal tyre according to the manualPressure
Dualtron Eagle10-inch wide, inner tube50 psi (3.45 bar)⁠[19]
Dualtron Spider 210-inch, inner tube50 psi (3.45 bar)⁠[20]
Dualtron Victor10-inch, inner tube50 psi (3.45 bar)⁠[21]
Dualtron Victor Luxury10-inch, inner tube50 psi (3.45 bar)⁠[22]
Dualtron Ultra 2 Up11-inch off-road, inner tube50 psi (3.45 bar)⁠[23]
Dualtron Togo9-inch, tubeless at the front, inner tube at the rear50 psi (3.45 bar)⁠[24]
Dualtron Togo Limited10 × 3.0250 kPa, or 2.5 bar (36 psi)⁠[25]
Dualtron DolphinTubeless at the front, solid tyre at the rear40 to 45 psi (2.76 to 3.10 bar)⁠[26]
Dualtron Sonic (Sonic Nano manual)8-inch, ‘self-sealing’2.5 bar (36 psi)⁠[27]
Minimotors manuals, figures recorded on 17 November 2026.

For other models in the catalogue, we found no figure published by the manufacturer. As of this survey, that is the case for the Dualtron Flip, Oriens and Ultra One, the Langfeite models, the Teverun Fighter 11 Plus, Fighter Supreme Ultra, 7260R and Space, the Kaabo Wolf King GTR MAX and the Nami Blast 2 Max, V1 Street and V2 Cross. In that case, read the maximum on your tyre's sidewall and write to us with a photo of the sidewall and the exact name of your model.

Psi, bar, kPa: how do you convert?

One psi is 6.894757 kPa, and one bar is 100 kPa⁠[28]. One bar is therefore about 14.5 psi. Manuals mix all three units: Minimotors mostly writes in psi, InMotion in psi and bar, Kaabo in kPa. The table below saves you the sum when it is time to inflate.

psibarkPa
302.07207
322.21221
352.41241
362.48248
382.62262
402.76276
453.10310
503.45345
513.52352
Conversions rounded to the nearest hundredth of a bar and the nearest kPa.

Should you inflate more depending on your weight or the temperature?

The Minimotors and Nami manuals give a single figure, with no adjustment for rider weight⁠[10]. When the manual gives a range, as InMotion and Teverun do, your weight helps you choose within it. Schwalbe sums it up for bicycles: the heavier the load, the higher the pressure should be⁠[33]. InMotion states that, within the range, a higher pressure gives you more distance per charge, and a lower pressure absorbs bumps better, especially on poor roads⁠[14].

A single figure in the manual

Aim for that figure, with no adjustment. Stay under the scooter's maximum load.

A range, light rider or poor roads

The bottom of the range absorbs bumps better. You lose a little distance per charge.

A range, heavy or loaded rider

Go for the top of the range, without exceeding the sidewall maximum.

Temperature matters too. When air cools, it contracts and the pressure drops, without any leak⁠[34]. Continental puts the drop at 0.07 to 0.14 bar for every 10 °C, for car tyres⁠[32]. Inflated at 20 °C in a heated garage, a tyre therefore loses 0.14 to 0.28 bar, or 2 to 4 psi, when you go out riding at 0 °C. In winter, check the pressure outdoors, at the temperature you ride in.

Conversely, a tyre that has just been ridden reads higher than its cold pressure. If you have to measure it hot, Michelin advises adding about 5 psi (0.34 bar) to the recommended cold figure⁠[30].

What does the pressure written on the tyre sidewall mean?

The sidewall often carries a MAX PRESS marking, or similar wording, followed by a figure in psi and sometimes in kPa. Michelin makes it clear: this is the tyre's maximum pressure, not necessarily the one for your vehicle. The figure to follow is still the manufacturer's⁠[29]. On a scooter, the manual therefore gives you the figure, and the sidewall gives you the limit.

  • MAX PRESS: the tyre's maximum pressure⁠[29]. Schwalbe puts it bluntly: never go outside the limits marked on the tyre, neither above the maximum nor below the minimum where there is one⁠[33].
  • MAX LOAD: the maximum load the tyre can carry⁠[29].
  • Tubeless or Tube type: without an inner tube, or with one⁠[29].
  • The size and the date code: how to read them is explained in our tyre article.

Over-inflated or under-inflated tyre: what are the risks?

Scooter wheel standing on the ground, tyre squashed and wide where it meets the ground
Under-inflated
Scooter wheel standing on the ground, tyre slightly flattened where it meets the ground
Correctly inflated
Scooter wheel standing on the ground, rounded tyre touching the ground over a small area
Over-inflated
If the pressure is…What you risk
Too lowMore punctures, as Teverun points out⁠[6]. Rapid wear and cracks on the sidewall⁠[33]. Less range⁠[14].
Very low or flatThe sidewalls collapse. The tyre is damaged inside and can go as far as bursting. It then becomes unrepairable, even for a hole in the tread⁠[31].
Too highA smaller contact area, less grip and a harsher ride⁠[30]. Less cushioning on poor roads⁠[14].
Above the sidewall maximumIncorrect pressure is one of the causes of blowouts listed by Pirelli⁠[34].

In our experience, an inner tube soon suffers in a soft tyre. Going up a kerb, it gets pinched between the tyre and the rim. And the tyre can creep round the rim until it tears the valve out. Either way, the tube has to be replaced: the method is in our puncture article.

How often should you check the pressure, and how?

All tyres lose air, even new ones⁠[30]. Michelin advises a check every two weeks, as well as before and during long journeys⁠[30]. InMotion goes further and asks you to check before every ride⁠[14].

Valve extension screwed onto the valve of a scooter wheel, next to the brake disc
An extension makes a valve tucked in by the disc or the motor easy to reach.
  1. Measure cold. For Michelin, a tyre is cold if it has not been ridden for at least two hours, or has covered less than 3.2 km at low speed⁠[30].
  2. Unscrew the valve cap. If the valve is hard to reach, screw an extension onto it, as the InMotion manual suggests⁠[14].
  3. Read the pressure with a reliable gauge, not with the air line at the petrol station⁠[30].
  4. Inflate to the figure for your model, without going over the sidewall maximum.
  5. Screw the valve cap back on. The Rovoron manuals remind you of this in their maintenance table⁠[12].
  6. While you are at it, go round the tyre: cuts, embedded objects, a bulge on the sidewall. The signs to know are in our tyre article.

If a tyre loses air from one week to the next, find the cause before topping it up yet again. Pirelli lists a faulty or badly fitted valve, a puncture, a leak at the rim and corrosion⁠[34]. A leaking tubeless valve should be replaced: we sell valves for Dualtron, Rovoron and Teverun scooters.

Sources

  1. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron Forever Product Manual
  2. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron Spider Max Product Manual
  3. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron Victor Limited Product Manual
  4. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron Victor Luxury Plus Product Manual
  5. Minimotors, English-language manual, spec sheet p. 6 and maintenance table p. 19, checked 17 November 2026, Rovoron R5 Product Manual
  6. Teverun, French-language manual of March 2024, maintenance p. 11, checked 17 November 2026, Manuel d'utilisation Teverun Fighter Mini, Blade Mini, Blade GT II
  7. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron Achilleus Product Manual
  8. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron New Storm Limited Product Manual
  9. Minimotors, English-language manual, version 2, spec sheet p. 7, checked 17 November 2026, Dualtron Alien Product Manual V2
  10. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron Thunder 3 Product Manual
  11. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron Thunder 2 Product Manual
  12. Minimotors, English-language manual, spec sheet p. 6 and maintenance table p. 19, checked 17 November 2026, Rovoron R7 Product Manual
  13. Minimotors, English-language manual, spec sheet p. 6 and maintenance table p. 20, checked 17 November 2026, Rovoron S7 Product Manual
  14. InMotion, English-language manual, specifications p. 10 and inflation p. 17, checked 17 November 2026, INMOTION RS User Manual
  15. InMotion, English-language manual, specifications p. 10 and inflation p. 17, checked 17 November 2026, INMOTION RS Lite User Manual
  16. InMotion, English-language manual, specifications p. 9 and inflation p. 17, checked 17 November 2026, INMOTION RS Jet User Manual
  17. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron X Limited Product Manual
  18. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron City Product Manual
  19. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron Eagle Product Manual
  20. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron Spider 2 Product Manual
  21. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron Victor Product Manual
  22. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron Victor Luxury Product Manual
  23. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron Ultra 2 Upgrade Product Manual
  24. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron Togo Product Manual
  25. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron Togo Limited Product Manual
  26. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron Dolphin Product Manual
  27. Minimotors, English-language manual, spec sheet p. 6, checked 17 November 2026, Dualtron Sonic Product Manual
  28. National Institute of Standards and Technology (NIST), Special Publication 811, Appendix B.8, checked 17 November 2026, NIST Guide to the SI, Appendix B.8: Factors for Units Listed Alphabetically
  29. Michelin, Car advice, updated 14 October 2026, checked 17 November 2026, Explication des marquages des pneus : comment lire un pneu ?
  30. Michelin, Motorcycle tyre reference card, Michelin North America (Canada), 2023, checked 17 November 2026, La conduite sécuritaire commence avec la pression d'air appropriée
  31. Michelin, Car advice, updated 26 February 2026, checked 17 November 2026, Est-ce que mon pneu est réparable ?
  32. Continental, Tyre advice, checked 17 November 2026, L'impact du froid sur la pression des pneus
  33. Schwalbe, Technology and FAQ, bicycle tyres, checked 17 November 2026, La pression de l'air
  34. Pirelli, Motorcycle tyre FAQ, checked 17 November 2026, FAQ sur les pneus moto : questions et réponses les plus fréquentes

About the author

Benjamin Gayaud

Benjamin Gayaud

Managing director of FōhzShop

He runs FōhzShop and develops EyeX, the app for Dualtron and Rovoron scooters. He personally tests the electric scooters the shop sells.

Read next

We use essential cookies for the service to work. With your consent, non-essential cookies for advertising may also be placed. You can accept or refuse these non-essential cookies.

Learn more: Cookie policy